當前位置：深圳瑞萊博激光科技有限公司>>co2激光雕刻切割機配件>>臺式二氧化碳激光功率計0-200瓦

臺式二氧化碳激光功率計0-200瓦

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號200w

品牌

廠商性質其他

所在地深圳市

在線詢價收藏產品查看聯系電話

塑料機械網采購部電話：0571-88918531QQ:2568841715

聯系方式：查看聯系方式

更新時間：2024-11-29 16:21:49瀏覽次數：124次

聯系我時，請告知來自塑料機械網

產品分類 品牌分類

暫無信息

深圳瑞萊博激光科技有限公司

經營模式：其他

商鋪產品：76條

所在地區：廣東深圳市

聯系人：閆晉華

詢價 給他留言

產品簡介

臺式二氧化碳激光功率計0-200瓦水冷

詳細介紹

產品描述

Introduction; Our power meter is water currency cooled power meter, it can measure up to 200w laser with good water
currency. It has big target area,high respond speed ,high accuracy ,good repeating usage . It use red led
screen to show the laser power, it is very convenient to read and necessary in laser lab and factory.
Parameters:
testing range:1-200w
Testing accuracy:+/-5%
Respond time: within 15seconds
Target area diameter:26mm
.wave length range:1.06um,10.6um,0.4-10.6um can be measured , have to be set up separately.
One time work hour: 24 hours continually with water currency.
Damage factors: beam diameter above 5-8mm, 1000w；beam dia below 2mm ,100w；without water currency for 20 seconds.

三：usage direction

press the key on the the panel, the screen will show 0
Put the power meter detector before the output end of the laser, make sure the laser beam goes to the center of the target area.
Put the detector close to the output end, in case the laser beam goes bent.
Read the number on the led screen when the laser goes to the target area, the number on the screen may increase ,
the biggest number is the power of the laser.
When testing high power laser, try to shorten the testing time, like test 100w laser, can last to the last digit stable.
500w when the the second digit from right stable.1000w when the second digit from the right increase
slowly then several numbers later, stop. In all try to short the testing time in case the detector temperature too high
, and damage the power meter.
Owing to small weight, the detector temperature can increase quickly, we can cool them by air cooling , like fans or wet cloth.，when use wet cloth don't let water on the target area, the power meter can be used again after this.
When the screen shows +, it means the battery is low, please change the battery.
When change the batteries, open the two screws at the bottom of the back cover..then pull the forward cover
backward, then turn. Then change the batteries is ok. The batteries is 12v.
Water currency: can have the water currency separately, can also use the same cooling water with the laser,
the laser water output end connect to the power meter water entrance ,the power meter water output connect to
the chiller.power meter's water end is the same don't have entrance and exit difference.